In modern times, water damage restoration usually following the following steps, using state of the art technology:
The goal of this is to get rid of the water from the surfaces. The use of industrial sump pumps and wet/ dry vacuum to get the water out is done and not just the manual way of using a dry rap and a bucket which is as less effective as it is efficient. These techniques provide the opportunity to extract water from the pads through carpets.
Drying and dehumidification
Structural drying is embarked upon with the use of advanced equipment and techniques and the goal is fast drying.
The quick-drying method affords less time for water to sit on a surface which would not only precipitate its break down but also cause colonization by mold and other fungi. These organisms cause a cocktail of health problems especially respiratory which includes wheezing, nasal stiffness, cough, throat irritation, sneezing, precipitate an asthmatic attack and so on; allergic reactions, eye irritation, skin irritation.
Mold growth can also cause organic breakdown of certain structures like wooden floors, drywall, and other home building organic structures which can lead to the replacement of the property, more expenditure on the home and more financial burden on whoever the cost falls on.
Since mold growth requires moisture, the key is to get rid of that moisture and fast and not just because of mold, other advantages of drying fast and early which are the prevention of:
- Rust of metal handles, doors, and other metal structures
- Damage to electronic devices
- Irreversible swelling of porous building materials.
The state of the art equipment that professionals use to achieve the goal is:
Low Grain Refrigerant(LGR) Dehumidifier-
It has the ability to reduce indoor relative humidity to about 10 percent, removing up to 16 gallons of water from the air per day of operation! Resulting in faster drying time, faster home restoration and life restoration.
Helps to absorb moisture from the air and release dry and warm air into the environment (5 percent relative humidity and 40-degree Celsius temperature). They usually operate well in humid areas. Commonly used in Silica gel.
It is a technique in which walls are dried without actually removing the drywall. The professional drills hole through the walls near the base, causing air to be forced into the cavities through these opening, rapidly reducing the drying time for the walls to less than it would take if other methods were used. The method is effective for situations where the water causing the damage originates from the room above that which is been treated. It helps avoid time delay and reduces the cost incurred in trying to replace whole walls, paint it and so on.
Not only do professional have these pieces of equipment, but they also have moisture detecting products like smart moisture detectors, special hygrometers, moisture sensors and so on.
Thorough methods are put in place to prevent the growth of mold as well as removal if it is already present.
Mold prevention by using tested and trusted antifungal and antimicrobial treatments which are used in moderate, environmental friendly quantities but still providing the desired effect of tackling mold growth.
Air scrubbers and high-efficiency particulate air (HEPA) vacuum are commonly used filtration equipment that professionals use to get the mold spore out of the air.
You have the freedom to choose the commercial or industrial units that meet all the needs. The commercial unit can absorb about 45 liters a day while the industrial type can absorb up to 240 liters per day.
The United States environmental protection agency (EPA) says that the air inside any home can be more polluted than the outdoor air. In fact, the agency says that the pollution inside the house could be a hundred times more than the outdoor air
As the hot summer approaches, the coastal cities are likely to be affected by typhoons and tornados. It is therefore necessary to have post-disaster restoration in place in advance to help people handle remediation and restoration issues.
Most dehumidifiers you will get on the market are of three types: desiccant dehumidifier, ionic membrane dehumidifier, and refrigeration dehumidifier.
Apart from being the lowest, it is the easiest to handle. Its evaporation rate is slow. It is only portions of a room or space that get affected, with the carpet getting slightly wet or even not wet at all.
Restoration can either be done by the homeowner or expert that are especially skilled in water damage repair. The advantage of having skilled labor involvement is that the experience they gathered from having to do the job repeatedly makes them better suited to handle the job. They also better and more sophisticated machines, the technical know how to operate them and the best methods to get the water out.
Whenever water damage comes up, contractors are usually quick to act because unlike the days of old where utter replacement of the damaged property is done for example, a carpet with mild damage may need replacement, due to the less technologically advanced methods of getting the water an out, hence incurring more cost for the insurance company or the individual.